GHQ Models Forums

I am placing my models on 1inch by 1 inch bases as per GHQ the game,but what about the towed pieces? Do I make them 1 inch by the length of the combination ?
Also I am having a problem with the paint coming off when I apply micro sol/set for the decals,any suggestions!

I am placing my models on 1inch by 1 inch bases as per GHQ the game,but what about the towed pieces? Do I make them 1 inch by the length of the combination ?

Its whatever you feel like doing. For me, I don't worry about it as I just use the firing gun, turn it 180, make sure that the towing vehicle is in base to base contact and say that its being towed. I find that this is the simple way for it.
Although I have seen pictures of other gamers actually basing the gun and towing vehicle together on 1 base and when the weapon needs to be towed, they replace the deployed weapon with the towed version.

Sepp, base them on separate 1 x 1 bases. That is the designer's intent. Happy gaming!

I do not usually use bases. 99+% of my figures are not based. I only base when I have a towing vehicle and a gun/trailor together or some sort of command, radar/radio/jamming, etc collection on a base. I have combined M577 TOC with: M577, & Hummv, & radio hummv, Elint system hummv or generator trailor, along with the commanders Hummv.

Sepp,

As far as the paint coming off when applying the micro sol... have you tried applying a layer of dullcote (or glosscote - your preference) to the model before applying decals? That's the approach I take and haven't had any problems.

Tanner

Sepp,

I second infobatte's suggestion, but with one modification -- use Glosscote, or a similar, glossy finish, before you apply decals. With a dull (matte) finish, it is much more likely to get air trapped under the decal, resulting in a "milky" finsh in the clear parts of the decal -- as well as a poor adhesion to the model. I have had excellent results giving my models a glossy finish, applying decals, then applying Dullcote after the decals have thoroughly dried. If you don't want to give your models a glossy finish before decaling, apply a drop of Future liquid floor wax where you want the decal to be, then apply the decal. I would still recommend applying Dullcote after the decal dries, to protect the decal and help bind it to the model.

I also apply Dullcote (after decaling) before weathering my models -- the dull finish gives more "tooth" to my weathering efforts.

One quick note about Dullcote -- and I guess this applies to any paint -- don't apply a single, heavy coat -- but rather a few light coats, with sufficient drying time between coats. If I remember correctly, Dullcote is lacquer-based, and if applied too heavily, it could react with the acrylics or enamels it is applied on top of... But I've had absolutely no problems as long as I've applied a couple of light coats. And I use it straight from the spray can; I would imagine one could get even finer coats by airbrushing it...

Hope this helps!

Regards,
Tom Stockton

Thanks for all the Info about size of bases and decals. Wow! having this forum makes
life so much easier and increases the fun of this hobby

Here is my method, super easy and wargame tested. This method will produce a decal that is super resistant to rubbing or flaking off. Also the edges will blend in so that there is no raised edge or noticeable seam-line.

Finish model except for mud and dirt if desired, before adding any dulcote.

Mix up a glue solution from either white glue and water or Modge-podge. This should be the consistency of watery milk.

Cut decal from sheet as close as possible to colored portions. A new x-acto and mag-glasses helps. Moisten decal in warm water on a plate.

Put a drop of water/glue on model where you want decal.

Position decal with small paintbrush. Let dry.

Add a drop of decal-set solution such as decal-set or Micro-sol. Don't move decal! Let dry thoroughly.

Add a final drop of water/glue to top of decal. Let dry - COMPLETELY!!

Add mud and/or dirt.

Dulcote.

Troy

I can consur that Troy's decal system is without THE BEST method I have ever used.

I've spent years trying to get them little ****ers to stay on with all the expensive Micro-water-You-gotta-use-this systems and they've all been outstanding wastes of time and money.

I actually use watered down PVA glue (as called in the UK) and I don't even need to matt coat it when it's dry as it dries flat anyway. It's the same stuff I use to flock the bases with as well, so even better.

Troy - you're a star

Cheers Dood,

Battler.