Canadian LAV III

shawno · Post by **shawno** » Sat Dec 30, 2006 5:56 am

Nicely done! I don't have what it takes to make LAV III's so I had to settle for coyotes. Have you given a crack at modeling the Leopard c2's with the MEXAS up armour package?

dougeagle · Post by **dougeagle** » Mon Jan 01, 2007 4:27 am

Sounds interesting enough. Is that pic an actual LAV-III from the net or is it the completed model that you have worked on?

chrisswim · Post by **chrisswim** » Mon Jan 01, 2007 8:08 am

Here is my suggestion.

First, I won an auction that had 10 LAV 25 turrets without the hulls. Then I used the Stryker CAV version and inserted the LAV 25 turret in the hole for the commanders weapon station. Worked perfectly! Now for 5 or 6 of these, I used the Stryker Cav dection/spotting 'box' and glued on left rear hull, on two i added telescopic pole to extend the device into the air for better survellience.

Any other good ideas?

shawno · Post by **shawno** » Mon Nov 05, 2007 10:41 am

chrisswim wrote:Here is my suggestion.

First, I won an auction that had 10 LAV 25 turrets without the hulls. Then I used the Stryker CAV version and inserted the LAV 25 turret in the hole for the commanders weapon station. Worked perfectly! Now for 5 or 6 of these, I used the Stryker Cav dection/spotting 'box' and glued on left rear hull, on two i added telescopic pole to extend the device into the air for better survellience.

Any other good ideas?

So with the LAV 25 turret, you can just drop it into the stryker cav no problem, or is it much harder then you make it out to be? Does it look proper?

Hey Cama, care to post a pic of your LAV III's?

Cheers....

Cpl_Blakeman · Post by **Cpl_Blakeman** » Mon Nov 05, 2007 10:29 pm

cama wrote:1. Take the turrets out of N-68. Toss the hulls into you bitz box. A bit of waste, kind of sucks. Oh well.

You could use those LAV hulls for Canadian Bison APCs, which as far as I know are just LAVs without turrets. Could also use them for recovery or maybe mortar vehicles as well.

av8rmongo · Post by **av8rmongo** » Mon Nov 05, 2007 11:56 pm

I think the Bison is more of an uparmored C2 version in that it has the same raised roof over the troop compartment.

Paul

shawno · Post by **shawno** » Tue Nov 06, 2007 3:52 am

av8rmongo wrote:I think the Bison is more of an uparmored C2 version in that it has the same raised roof over the troop compartment.

Paul

Having worked in them, this would be a more accurate description of the Bison.

chrisswim · Post by **chrisswim** » Tue Nov 06, 2007 8:22 am

Instead of putting the CAV hatch and machine gun & sighting. I used the LAV 25 turret. Pretty easy to me. Try it with out glue, see if you like it.

shawno · Post by **shawno** » Tue Nov 06, 2007 9:09 am

chrisswim wrote:Here is my suggestion.

First, I won an auction that had 10 LAV 25 turrets without the hulls. Then I used the Stryker CAV version and inserted the LAV 25 turret in the hole for the commanders weapon station. Worked perfectly! Now for 5 or 6 of these, I used the Stryker Cav dection/spotting 'box' and glued on left rear hull, on two i added telescopic pole to extend the device into the air for better survellience.

Any other good ideas?

Chris sounds like you're describing a LAV III version of the LAV II coyote...any pics?

and chris did you dremel anything down?

shawno · Post by **shawno** » Wed Nov 07, 2007 9:39 am

cama, sorry to bug, but could you post that pic of your LAV if you have it handy? cheers...

chrisswim · Post by **chrisswim** » Thu Nov 08, 2007 1:56 am

Shawno,

I may be LAV II Coyote, just used Styker CAV hull & paired it with LAV 25 turret to replicate the Canadian vehicle as shown above in the post.

On the back left corner on the hull put the Styker CAV sighting/targeting box, glueing to the hull, two I have elevated for survellience.

I will try to work on photos.....
Chris

shawno · Post by **shawno** » Fri Nov 09, 2007 9:17 am

Great job Cama, good insight for me.

Thanks!!

Canadian LAV III

Re: Canadian LAV III

Re: Canadian LAV III