Stripping paint off infantry.

This is a general forum for all types of posts related to Military models.

Moderators: dnichols, GHQ, Mk 1

Post Reply
cabin4clw
E5
Posts: 104
Joined: Mon Jan 03, 2005 5:45 am
Location: West Michigan

Stripping paint off infantry.

Post by cabin4clw »

I want to get my infantry off their round bases which are flocked in order for me to strip them of paint and prime, and paint them again. I just want them to look better..
I just do not know how to proceed when they are in the green stuff and then how to rinse them without the infantry going all over the place.
Any help would be great.
Hope this makes sense because of my meds to treat my pneumonia.

madman
E5
Posts: 210
Joined: Sat Nov 19, 2016 9:21 pm
Location: Ontario Canada

Post by madman »

What glue did you use to attach the figures and what are the bases made of?

As an example I used superglue 30+ years ago and 1/2" square thin (under .030") plastic bases and 3 of the 4 figures on each would just pop off when I flexed the plastic. On probably 90% of the remaining ones a careful pry with an exacto popped the last off. Those that didn't usually tore part of the base out. Again a careful cut between base and figure separated another 90%. The last ones were buggers and usually destroyed them.

As to stripping paint I used a one to two week soak in Yellow Pinesol. Then light brushing with a wire brush about the size of a toothbrush. It sounds aggressive but the minis held up. I only use enamels and the paint has varied in age from under a week to 40+ years.

mike robel
E5
Posts: 152
Joined: Tue Mar 21, 2017 12:41 am

Post by mike robel »

Nothing works. Get infantry to clean up (or arguing with them) is like wrestling with a pig, everyone gets muddy and the pig loves it.

To break superglue bonds, you can try freezing the parts and then twisting them gently.

I've done it with plastic, resin (used for some model parts), and some metal parts.. :roll:

redleg
E5
Posts: 3809
Joined: Fri Dec 17, 2004 11:02 am
Location: Riverside, CA

Post by redleg »

[quote="mike robel"]Nothing works. Get infantry to clean up (or arguing with them) is like wrestling with a pig, everyone gets muddy and the pig loves it.
. :roll:[/quote]

LOL gotta love the grunts!

panzergator
E5
Posts: 3465
Joined: Thu Oct 08, 2015 3:44 am

Post by panzergator »

Gen. Creighton Abrams (an ARMOR guy, incidentally) used it in VN to discourage his PAOs from arguing with the press. "When you wrestle with pigs, you both get dirty, but the pigs like it."

If your infantry was affixed to a base with Cyano-acrylate (super glue), you can use fingernail polish. The active ingredient in it is acetone, which you can purchase in the paint section of Home Depot. READ THE WARNINGS, HOWEVER. It is hazardous, requires ventilation and both the liquid and fumes are flammable. It also strips paint. Don't use a plastic container. Recommend steel or glass.
Last edited by panzergator on Wed Jan 29, 2020 10:02 am, edited 1 time in total.
All blessings flow from a good mission statement.
Pogo was right. So was Ike.
"A Gentleman is a man who is only rude intentionally." (Churchill)
Give credit. Take responsibility.

cabin4clw
E5
Posts: 104
Joined: Mon Jan 03, 2005 5:45 am
Location: West Michigan

Post by cabin4clw »

The glue is I believe pva.

panzergator
E5
Posts: 3465
Joined: Thu Oct 08, 2015 3:44 am

Post by panzergator »

Might work. Try the fingernail polish, rather than buy a can of acetone.
All blessings flow from a good mission statement.
Pogo was right. So was Ike.
"A Gentleman is a man who is only rude intentionally." (Churchill)
Give credit. Take responsibility.

Post Reply